|
|
 |
|
|
| 1. 求救：7206加了块PA-MC-8TE1+不能使用 |
  |
|
 |
|
HP : 0 / 269
MP : 54 / 3671
EXP : 78%
|
|
武林奇才
成员等级: 11
发表总数: 162
金币总数: 707
所属组别: 普通成员
注册日期: 2004/05/12
|
在配置工具里有些模块查不到，检测不了情况，请各位大仙 出手襄助.......
配置是这样的:
MEM-I/0-FLCl6M
NPE225
C7200-I/0-FE
RIGHT ADAPTER： PA-4T+ PA-FE-TX （PA-MC-8TE1+）加上去不能用，show diag 可以查看到信息,但是不能进入接口模式
LEFT ADAPTER : PA-4T+ PA-8T-V35 VPA-4E1G/75
IOS都试好几个了: c7200-jk9o3s-mz.124-1a.bin c7200-jo3s-mz.123-5a.B5.bin c7200-is-mz.123-7.XI6.bin
想吾要，试下拉，信吾信，一水壶，坼你噶头，交剪脚，哎呀....(再来一次)...交剪脚,哎呀.... |
|
|
|
| 2. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 0 / 269
MP : 54 / 3671
EXP : 78%
|
|
武林奇才
成员等级: 11
发表总数: 162
金币总数: 707
所属组别: 普通成员
注册日期: 2004/05/12
|
修正一个错误：NPE150----NPE225
想吾要，试下拉，信吾信，一水壶，坼你噶头，交剪脚，哎呀....(再来一次)...交剪脚,哎呀.... |
|
|
|
| 3. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
 |
|
HP : 67 / 678
MP : 337 / 10313
EXP : 14%
|
|
名动江湖
成员等级: 28
发表总数: 1012
金币总数: 906
所属组别: 高级成员
注册日期: 2003/10/28
|
用software adviosr去匹配个软件看看
软件版本不够,认不出来是很正常的事情 |
|
|
|
| 4. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 0 / 269
MP : 54 / 3671
EXP : 78%
|
|
武林奇才
成员等级: 11
发表总数: 162
金币总数: 707
所属组别: 普通成员
注册日期: 2004/05/12
|
我的是：C7200-I/0-FE（单个快速以太口的I/0），对应着应该是1 port use of
2-port Fast Ethernet (TX) 吧
2-port Fast Ethernet (TX)
PA-2FE-TX
High
400
2.4 MB
—
1 port use of
2-port Fast Ethernet (TX)
PA-2FE-TX 5
High
200
2.4 MB
—
4-port synchronous serial, enhanced
PA-4T+
Low 3
0
0.20 MB
—
8-port synchronous serial (V.35)
PA-8T-V35
Low 3
0
0.35 MB
—
8-port multichannel T1/E1 PRI
PA-MC-8TE1+
Low 3
0
10 MB
在没有加PA-MC-8TE1+之前所有的模块均正常
统计：2 HIGH 4 LOW Bandwidth Points :800
(这里 假设I/0-FE/E 和 PA-FE-TX 均算bank-width为400)
PA-4E1G/75查不到对应的bank-width的值，没有算进去)
PA-4E1G/120 band-width为0，应该都是low来计算，那么一算都没有超过标准，应该是个可行的配置才对啊..
为什么加PA-MC-8TE1+不能用啊？（排除硬件问题）
Requirements Summary
NPE-G1
•Left side, bus 1 (slots 1, 3, and 5) and I/O controller (slot 0) has a 600 point maximum.
•Right side, bus 2 (slots 2, 4, and 6) has a 600 point maximum.
•Distribute port adapter bandwidth points evenly across both left and right system slots (buses).
•Do not calculate bandwidth points for an I/O controller if an I/O controller is installed with the NPE-G1.
•The NPE-G1 Gigabit Ethernet interfaces do not use bandwidth points.
NPE-400, NPE-300, NSE-1
•Left side, bus 1 (slots 1, 3, and 5) and I/O controller (slot 0) has a 600 point maximum.
•Right side, bus 2 (slots 2, 4, and 6) has a 600 point maximum.
•Distribute port adapter bandwidth points evenly across both left and right system slots (buses).
NPE-225, NPE-200, NPE-175, NPE-150
•Port adapters are labeled as high, medium, and low.
•Bandwidth point rules:
–No more than three high-bandwidth port adapters, and
–No more than five total medium- and high-bandwidth port adapters, and
– No more than 800 total bandwidth points per system
•Distribute port adapter bandwidth points evenly across both left and right system slots (buses).
NPE-100
•Port adapters are labeled as high, medium, and low.
•Bandwidth point rules:
–No more than two high-bandwidth port adapters, and
–No more than four total medium- and high-bandwidth port adapters, and
– No more than 800 total bandwidth points per system
•Distribute port adapter bandwidth points evenly across both left and right system slots (buses).
想吾要，试下拉，信吾信，一水壶，坼你噶头，交剪脚，哎呀....(再来一次)...交剪脚,哎呀.... |
|
|
|
| 5. RE: 求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 0 / 269
MP : 54 / 3671
EXP : 78%
|
|
武林奇才
成员等级: 11
发表总数: 162
金币总数: 707
所属组别: 普通成员
注册日期: 2004/05/12
|
| QUOTE | 用software adviosr去匹配个软件看看
软件版本不够,认不出来是很正常的事情 |
排除了是IOS的问题，我用c7200-jo3s-mz.123-5a.B5.bin
Minimum Cisco IOS® Release Supported Cisco 7200/7301-12.2(12), 12.2(12)T, 12.1(14), 12.1(12)E, 12.0(22)S, 12.2(14)S, and later IOS versions
Cisco 7304-12.2(20)S and later IOS versions
Cisco 7500-12.2(13)T, 12.2(11)S, 12.1M, 12.2M, 12.0(22)S, and 12.1 (13E IOS versions
Cisco 7600-FlexWAN 12.1(13)E9 and 12.2(14)SX; Enhanced FlexWAN 12.2(14)SX IOS version
我觉得我上面计算BAND-WIDTH可能还不太正确.....
想吾要，试下拉，信吾信，一水壶，坼你噶头，交剪脚，哎呀....(再来一次)...交剪脚,哎呀.... |
|
|
|
| 6. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
 |
|
HP : 250 / 1254
MP : 1625 / 21993
EXP : 16%
|
|
迟则生变
成员等级: 51
发表总数: 4877
金币总数: 308
所属组别: 管理员
注册日期: 2003/01/9
|
怎么个“不能使用”？
card type e1 命令配了没有？
没有谁能像一座孤岛/在大海里独踞/每个人都像一块小小的泥土/连接成整个陆地/如果一块泥土被海水冲去/欧洲将缺其一隅/这如同一座山岬/也如同你的朋友和你自己/无论谁死了/都是自己的一部分在死去/因为我包含在人类这个概念里/因此我从不问丧钟为谁而鸣/它为我，也为你
No man is an Island, entire of itself; every man is a piece of the Continent, a part of the main; if a clod be washed away by the sea, Europe is the less, as well as if a promontory were, as well as if a man or of thy friends or of thine own were; any man's death diminishes me, because I am involved in Mankind; And therefore never send to know for whom the bell tolls; It tolls for thee.
|
|
|
|
| 7. RE: 求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 0 / 269
MP : 54 / 3671
EXP : 78%
|
|
武林奇才
成员等级: 11
发表总数: 162
金币总数: 707
所属组别: 普通成员
注册日期: 2004/05/12
|
| QUOTE | 怎么个“不能使用”？
card type e1 命令配了没有？ |
谢谢麦子的指示，试下...
一定要用这个命令才可以进入controller t1 的模式嘛？
想吾要，试下拉，信吾信，一水壶，坼你噶头，交剪脚，哎呀....(再来一次)...交剪脚,哎呀.... |
|
|
|
| 8. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 0 / 269
MP : 54 / 3671
EXP : 78%
|
|
武林奇才
成员等级: 11
发表总数: 162
金币总数: 707
所属组别: 普通成员
注册日期: 2004/05/12
|
show ver 里面都没有PA-MC-8TE1+硬件信息，其他的模块有显示，但是show diag可以看得见全部模块信息...
等待进一步观察..
想吾要，试下拉，信吾信，一水壶，坼你噶头，交剪脚，哎呀....(再来一次)...交剪脚,哎呀.... |
|
|
|
| 9. RE: 求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 0 / 269
MP : 54 / 3671
EXP : 78%
|
|
武林奇才
成员等级: 11
发表总数: 162
金币总数: 707
所属组别: 普通成员
注册日期: 2004/05/12
|
| QUOTE | 怎么个“不能使用”？
card type e1 命令配了没有？ |
麦子...你实在令我太佩服了...我的问题就是如下所描述...加个card type e1 6 应该没问题，下午就去试下，谢谢麦子
http://www.ciscotaccc.com/core/showcase?case=K19239995
Search Result
Solution # K19239995
Title A T1 and E1 combination port adapter does not show up in the show run or show version command output due to the card type command not being configured
Core issue All of the PA-MCX, PA-VXA, PA-VXB, PA-VXC, and PA-MC-8TE1+ card port adapters are not seen in the output of either the show run command or the show version command. However, these port adapters are seen in the output of the show diag command. This occurs if the card type command is not configured. This is due to the fact that these port adapters can operate as either T1 or E1 mode, depending on the card type command configuration.
The controller t1 or controller e1 global configuration commands fail if the card type command is not configured first.
Resolution If after installing any combination of T1 and E1 port adapters, the controller t1 or controller e1 global configuration commands are not accepted, yet the port adapter is recognized in the show diag command output, perform the following steps to enable the port adapter for configuration:
Determine the slot number where the port adapter is installed by issuing the show diag command. If the port adapter is installed in a Versatile Interface Processor (VIP), also determine the port adapter bay.
7513#show diag
Slot 9:
Physical slot 9, ~physical slot 0x6, logical slot 9, CBus 0
Microcode Status 0x4
Master Enable, LED, WCS Loaded
Board is analyzed
Pending I/O Status: None
EEPROM format version 1
VIP6-80 RM7000B controller, FRU: VIP6, HW rev 2.01, board revision A0
Serial number: 29328007 Part number: 73-8117-01
Test history: 0x00 RMA number: 00-00-00
Flags: cisco 7000 board; 7500 compatible
EEPROM contents (hex):
0x20: 01 4E 02 01 01 BF 82 87 49 1F B5 01 00 00 00 00
0x30: 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Slot database information:
Flags: 0x4 Insertion time: 0x32B962B4 (00:01:45 ago)
Controller Memory Size: 256 MBytes CPU SDRAM, 64 MBytes Packet SDRAM
PA Bay 1 Information:
8 port, software configurable Multichannel T1/E1 without TDM Port Adapter
EEPROM format version 4
HW rev 2.00, Board revision A0
Serial number: JAE071109NF Part number: 73-7549-02
This example shows the port adapter is installed in VIP PA Bay 1 in slot 9 of the router.
Issue the card type {t1 | e1} slot [bay] command to enable the port adapter. For example, to enable the port adapter as a T1 interface, the command would be card type t1 9 1.
If the router is a Cisco 7200 series router, where the port adapter is installed directly into a router slot (rather than a VIP), the command requires only the slot number. The command does not require the bay number. For example, to enable a port adapter in slot 2 of a Cisco 7200 series router as an E1 interface, the command is card type e1 2.
After the card type command is issued, the interface can be configured by issuing the controller {t1 | e1} slot port global configuration command.
Problem Type Hardware component does not work
When Problem Occurs After hardware installation or replacement, After software configuration change
Platform Type Cisco 7200 or uBR 7200 Series, Cisco 7500 Series
Port Adapters for 7200 and 7500 Routers PA-MC-8TE1+, PA-MCX-2TE1 (multichannel T1/E1 PA), PA-MCX-4TE1, PA-MCX-8TE1, PA-MCX-8TE1-M, Port adapters not listed
Direct URL http://www.ciscotaccc.com/core/showcase?case=K19239995
还想请教下：像这样的问题，在cisco里面用什么“关键字”进行搜索啊.....
我搜索：PA-MC-8TE1+ 7206 PA-MC-8TE1+ card type e1 PA-MC-8TE1+ configuration等都不能找到
最后是看见有些文档有command的字符，用 PA-MC-8TE1+ command 搜索看到这个答案的....
想吾要，试下拉，信吾信，一水壶，坼你噶头，交剪脚，哎呀....(再来一次)...交剪脚,哎呀.... |
|
|
|
| 10. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 250 / 1254
MP : 1625 / 21993
EXP : 16%
|
|
迟则生变
成员等级: 51
发表总数: 4877
金币总数: 308
所属组别: 管理员
注册日期: 2003/01/9
|
Cisco Document Home> http://www.cisco.com/univercd/home/home.htm
Router>7206> http://www.cisco.com/univercd/cc/td/doc/pr.../7206/index.htm
Cisco 7200 Series Routers Port Adapter Documentation Roadmap> http://www.cisco.com/univercd/cc/td/doc/pr...7200vx/3530.htm
* 8-port Multichannel T1/E1 8PRI Port Adapter Installation and Configuration PA-MC-8TE1+= > http://www.cisco.com/univercd/cc/td/doc/pr...rt_t1/index.htm
Configuring the PA-MC-8TE1+ > http://www.cisco.com/univercd/cc/td/doc/pr..._t1/2738cfg.htm
没有谁能像一座孤岛/在大海里独踞/每个人都像一块小小的泥土/连接成整个陆地/如果一块泥土被海水冲去/欧洲将缺其一隅/这如同一座山岬/也如同你的朋友和你自己/无论谁死了/都是自己的一部分在死去/因为我包含在人类这个概念里/因此我从不问丧钟为谁而鸣/它为我，也为你
No man is an Island, entire of itself; every man is a piece of the Continent, a part of the main; if a clod be washed away by the sea, Europe is the less, as well as if a promontory were, as well as if a man or of thy friends or of thine own were; any man's death diminishes me, because I am involved in Mankind; And therefore never send to know for whom the bell tolls; It tolls for thee.
|
|
|
|
| 11. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 67 / 678
MP : 337 / 10313
EXP : 14%
|
|
名动江湖
成员等级: 28
发表总数: 1012
金币总数: 906
所属组别: 高级成员
注册日期: 2003/10/28
|
哈哈，麦子大哥果然熟练,
cisco认证最大的帮助就是会很好的查文档
|
|
|
|
| 12. Re: 求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
 |
|
HP : 0 / 148
MP : 21 / 2403
EXP : 95%
|
|
拜师学艺
成员等级: 6
发表总数: 65
金币总数: 108
所属组别: 普通成员
注册日期: 2003/07/3
|
顺便问问,有没有人碰到过PA-8T-V35的那张卡逻辑第7口对应的是物理线路第3根,反正不是0-7顺序排列的情况,如果有,请帮忙列出对应关系和原因,谢谢!! |
|
|
|
| 13. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 0 / 269
MP : 54 / 3671
EXP : 78%
|
|
武林奇才
成员等级: 11
发表总数: 162
金币总数: 707
所属组别: 普通成员
注册日期: 2004/05/12
|
PA-MC-8TE1+已经可以配置端口，但模块有红色报警灯....
什么原因？请麦子再出手....
Cisco7206a#show ver
Cisco Internetwork Operating System Software
IOS ™ 7200 Software (C7200-JO3S-M), Version 12.3(5a)B5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 1986-2005 by cisco Systems, Inc.
Compiled Wed 11-May-05 14:06 by leccese
Image text-base: 0x60008AF4, data-base: 0x62058000
ROM: System Bootstrap, Version 12.2(1r) [dchih 1r], RELEASE SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-JO3S-M), Version 12.3(5a)B5, RELEASE SOFTWARE (fc1)
Cisco7206a uptime is 1 week, 21 hours, 30 minutes
System returned to ROM by power-on
System image file is "disk0:c7200-jo3s-mz.123-5a.B5.bin"
cisco 7206 (NPE225) processor (revision A) with 114688K/16384K bytes of memory.
Processor board ID 12163034
R527x CPU at 262MHz, Implementation 40, Rev 10.0, 2048KB L2 Cache
6 slot midplane, Version 1.3
Last reset from power-on
G.703/E1 software, Version 1.0.
G.703/JT2 software, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
Channelized E1, Version 1.0.
Number of Fast PAs = 2
Number of Fast+Medium PAs = 2
Total number of PA bandwidth points = 400
2 FastEthernet/IEEE 802.3 interface(s)
20 Serial network interface(s)
8 Channelized E1/PRI port(s)
125K bytes of non-volatile configuration memory.
47040K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
16384K bytes of Flash PCMCIA card at slot 1 (Sector size 128K).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x102
Cisco7206a#sho env
All measured values are normal
Cisco7206a#
Cisco7206a# sho diag
Slot 0:
Fast-ethernet on C7200 I/O card with MII or RJ45 Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time 1w0d ago
EEPROM contents at hardware discovery:
Hardware revision 1.3 Board revision C0
Serial number 12640367 Part number 73-2956-02
FRU Part Number: C7200-IO-FE-MII/RJ45=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 83 01 03 00 C0 E0 6F 49 0B 8C 02 00 00 00 00
0x10: 60 00 00 00 99 02 09 00 00 FF FF FF FF FF FF FF
Slot 1:
Fast-ethernet (TX-ISL) Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time 1w0d ago
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision B0
Serial number 11554112 Part number 73-1688-04
FRU Part Number: PA-FE-TX
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 11 01 01 00 B0 4D 40 49 06 98 04 00 00 00 00
0x10: 58 00 00 00 99 03 02 00 FF FF FF FF FF FF FF FF
Slot 2:
Mx serial (ME1-UNBAL) Port adapter, 4 ports
Port adapter is analyzed
Port adapter insertion time 1w0d ago
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision C0
Serial number 16404413 Part number 73-2231-04
FRU Part Number: PA-4E1G/75=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 41 01 01 00 FA 4F BD 49 08 B7 04 00 00 00 00
0x10: 60 00 00 00 99 12 16 00 FF FF FF FF FF FF FF FF
Slot 3:
Mx serial (ME1-UNBAL) Port adapter, 4 ports
Port adapter is analyzed
Port adapter insertion time 1w0d ago
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision D0
Serial number 29565236 Part number 73-2231-04
FRU Part Number: PA-4E1G/75=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 41 01 01 01 C3 21 34 49 08 B7 04 00 00 00 00
0x10: 68 00 00 00 02 11 22 00 FF FF FF FF FF FF FF FF
Slot 4:
Mx serial (ME1-UNBAL) Port adapter, 4 ports
Port adapter is analyzed
Port adapter insertion time 1w0d ago
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision C0
Serial number 21193663 Part number 73-2231-04
FRU Part Number: PA-4E1G/75=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 41 01 01 01 43 63 BF 49 08 B7 04 00 00 00 00
0x10: 60 00 00 00 00 07 12 00 FF FF FF FF FF FF FF FF
Slot 5:
PA-MC-8TE1 Plus Port adapter, 8 ports
Port adapter is analyzed
Port adapter insertion time 1w0d ago
EEPROM contents at hardware discovery:
Hardware Revision : 3.0
PCB Serial Number : JAE0826MSCU
Part Number : 73-7549-03
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0-0
Product (FRU) Number : PA-MC-8TE1+
Top Assy. Part Number : 800-19387-03
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 4E 41 03 00 C1 8B 4A 41 45 30 38 32
0x10: 36 4D 53 43 55 82 49 1D 7D 03 42 41 30 03 00 81
0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D
0x30: 4D 43 2D 38 54 45 31 2B 20 20 20 20 20 20 20 20
0x40: 20 C0 46 03 20 00 4B BB 03 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Cisco7206a#show run
controller E1 5/0
channel-group 0 timeslots 1-31
!
controller E1 5/1
channel-group 0 timeslots 1-31
!
controller E1 5/2
channel-group 0 timeslots 1-31
!
controller E1 5/3
channel-group 0 timeslots 1-31
!
controller E1 5/4
channel-group 0 timeslots 1-31
!
controller E1 5/5
channel-group 0 unframed
!
controller E1 5/6
channel-group 0 timeslots 1-31
!
controller E1 5/7
channel-group 0 timeslots 1-31
!
Cisco7206a#sho contr e1
E1 5/0 is up.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
International Bit: 1, National Bits: 11111
Data in current interval (54 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 94 Unavail Secs
E1 5/1 is up.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
International Bit: 1, National Bits: 11111
Data in current interval (59 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 209 Unavail Secs
E1 5/2 is up.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
International Bit: 1, National Bits: 11111
Data in current interval (59 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 215 Unavail Secs
E1 5/3 is up.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
International Bit: 1, National Bits: 11111
Data in current interval (62 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 219 Unavail Secs
E1 5/4 is up.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
International Bit: 1, National Bits: 11111
Data in current interval (63 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 222 Unavail Secs
E1 5/5 is down.
Applique type is Channelized E1 - balanced
Receiver has loss of signal.
alarm-trigger is not set
Framing is UNFRAMED, Line Code is HDB3, Clock Source is Line.
Data in current interval (64 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 226 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
E1 5/6 is up.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
International Bit: 1, National Bits: 11111
Data in current interval (64 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 229 Unavail Secs
E1 5/7 is up.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
International Bit: 1, National Bits: 11111
Data in current interval (65 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 232 Unavail Secs
controller E1 5/5
channel-group 0 unframed
是特意改成这样的///
没有接线，对端口进行打环测试，可以ping 通
Cisco7206a(config)#int s5/4:0
Cisco7206a(config-if)#ip add 192.168.100.1 255.255.255.0
Cisco7206a(config-if)#loo
Cisco7206a(config-if)#loopback int
Cisco7206a(config-if)#loopback internal
Cisco7206a(config-if)#end
Cisco7206a#ping 192.168.100.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.100.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
Cisco7206a#
想吾要，试下拉，信吾信，一水壶，坼你噶头，交剪脚，哎呀....(再来一次)...交剪脚,哎呀.... |
|
|
|
| 14. Re:求救：7206加了块PA-MC-8TE1+不能使用 |
|
|
|
|
|
HP : 250 / 1254
MP : 1625 / 21993
EXP : 16%
|
|
迟则生变
成员等级: 51
发表总数: 4877
金币总数: 308
所属组别: 管理员
注册日期: 2003/01/9
|
将未使用的端口shutdown，保证在用端口状态为UP，模块告警灯就灭啦。 | |
